300 CDL practice questions covering general knowledge, air brakes, combination vehicles, hazardous materials, and all endorsements. Study for your Class A, B, or C commercial driver's license with confidence.
Try your first 25 questions free. Continue with a paid plan.
Vehicle inspection, basic control, shifting, backing, and safe driving fundamentals
Air brake system components, inspection, operation, and emergency procedures
Coupling/uncoupling, rollover prevention, jackknifing, and trailer skids
Engine compartment, cab interior, exterior walk-around, and brake checks
Placarding, shipping papers, loading rules, and emergency response
Liquid surge, baffles, smooth bore tanks, and weight distribution
Coupling procedures, stability, inspection, and turning techniques
Passenger safety, loading/unloading, emergency exits, and ADA compliance
Driving limits, rest requirements, ELD regulations, and record of duty status
Steering, suspension, tires, lighting, and cargo securement
The low-pressure warning device (light, buzzer, or wig-wag) must activate before the air pressure drops below 60 psi. This warning alerts the driver that air pressure is getting dangerously low and the spring brakes may apply automatically. During a pre-trip inspection, you should fan the brakes to reduce pressure and verify the warning activates at or before 60 psi. If it does not, the vehicle should not be driven.
For a combination vehicle (tractor-trailer), the maximum allowable air loss rate is 4 psi per minute with the engine off, brakes fully applied, and after initial pressure drop stabilizes. For a single vehicle, the maximum is 3 psi per minute. A loss rate exceeding these limits indicates an air leak that must be repaired before operating the vehicle. This is part of the applied-pressure leakage test during pre-trip inspection.
When the drive wheels lock up, the rear of the tractor tends to swing out because the locked tires lose traction and the trailer pushes the tractor. This is a tractor jackknife. The trailer stays in a straight line while the tractor swings sideways, forming a V-shape. To correct, release the brakes to allow the drive wheels to regain traction. Anti-lock braking systems (ABS) help prevent wheel lockup but the driver should still use controlled braking techniques.
Under FMCSA hours of service rules for property-carrying drivers, you may drive a maximum of 11 hours after 10 consecutive hours off duty. Additionally, you cannot drive beyond the 14th consecutive hour after coming on duty (the 14-hour window), and you must take a 30-minute break after 8 cumulative hours of driving. The 60/70-hour rule further limits total on-duty time over 7 or 8 consecutive days.
Before coupling, the fifth wheel should be tilted down toward the rear of the tractor and the locking jaws should be in the open position. This angle allows the trailer kingpin to slide smoothly into the fifth wheel throat and engage the locking jaws. After coupling, the driver must verify the connection by performing a tug test (pulling gently against the trailer brakes) and visually inspecting that the locking jaws are closed around the kingpin with no gap between the upper and lower fifth wheel.
Liquid surge occurs when the liquid inside a partially loaded tank moves forward, backward, or sideways in response to vehicle movement. When braking, the liquid surges forward and pushes the truck forward, increasing stopping distance. On curves, side-to-side surge can cause rollover. Baffled tanks reduce front-to-back surge but do not prevent side-to-side surge. Smooth bore (unbaffled) tanks used for food-grade products have the most surge. Drivers should use smooth, gradual braking and reduce speed on curves.
Placards are required when hauling 1,001 pounds or more of a hazardous material in a single class (Table 2 materials). However, certain highly dangerous materials (Table 1) such as explosives, poison gas, and radioactive materials require placards at any quantity, even one pound. Placards must be placed on all four sides of the vehicle (front, back, and both sides) and must be readable from 50 feet away.
At 55 mph, the total stopping distance for a loaded tractor-trailer on dry pavement is approximately 390 feet, which is about the length of a football field plus both end zones. This includes perception distance (about 60 feet), reaction distance (about 60 feet), and braking distance (about 270 feet). On wet pavement, stopping distance can double. This is why following distance of at least 6-7 seconds is recommended for commercial vehicles at highway speeds.
A thorough steering system inspection includes checking the steering wheel for excessive free play (should not exceed approximately 10 degrees or about 2 inches of movement on a 20-inch wheel before the front tires begin to move). Additionally, check the power steering fluid level, inspect hoses and connections for leaks, check the steering linkage and gear box for looseness or damage, and ensure the steering column is securely mounted. Steering defects are critical safety items that can put the vehicle out of service.
You should always downshift to a gear low enough to control speed before starting down a long or steep downgrade. Engine braking (the retarding force of the engine) should be the primary method of speed control on downgrades. Use the brakes only as a supplement and apply them in a snub-braking pattern (apply firmly to reduce speed 5 mph below safe speed, then release). Riding the brakes continuously causes brake fade from overheating, which can lead to complete brake failure.
Access all 300 CDL practice questions with detailed explanations.
Start ExamWe offer 300 CDL practice questions covering general knowledge, air brakes, combination vehicles, and all endorsement categories including hazmat, tanker, doubles/triples, passenger, and school bus.
Your first 25 questions are free. Continue beyond 25 questions with a paid plan.
The test covers general knowledge, air brakes, combination vehicles, pre-trip inspection, hazardous materials, tanker vehicles, doubles and triples, passenger transport, hours of service, and vehicle systems and safety.
Most states require a score of 80% or higher on the CDL knowledge tests. The general knowledge test typically has 50 questions, the air brakes test has 25, and endorsement tests have 20-30 questions each. Our practice questions are designed to match the difficulty and format of your state's actual CDL exam.
Check FMCSA requirements and your state DMV, or grab a CDL study guide for all endorsements.
CDL Requirements View Study Guides